Products
Tripod Barrier Kaba Kerberos TPB-E02
Manufacturer: KABA Gallenschutz
Country of origin: Germania
Website: http://www.kaba.com/physical-access-systems/
Product code: Kaba TPB-E02
-
Measurements:
Usable bar length:
510 mm
Width:
770 mm
Height:
1020 mm
Depth:
1170 mm
Construction:
The housing and the base columns are made of semi-gloss AISI 304 stainless steel. Base columns are empty and can be used to integrate customer components. The rotation head and other electrical and mechanical elements are integrated into the centre housing. In case of multiple installations, the housing unit acts as a guiding element – additional guiding bars are not required. To improve personal safety, standards and guidelines relating to points where body parts could get pinched or squashed have been taken into account in the development of the tripod barrier (Machinery Directive 2006/42/EC).
Finish:
AISI 304 stainless steel with smooth semi-gloss finish.
Function:
□ Aggregate type 0
The rigid crossbars are made of stainless steel. The tripod barrier is mechanically free in one direction, the opposite direction is blocked. The rotary motion is initiated manually.
alternatively
□ Aggregate type 1.1
The rigid crossbars are made of stainless steel. One direction is controlled electrically while the opposite direction remains blocked. Passage is released in one direction after a release impulse. The rotary motion is initiated manually. The unit can only be passed through by the user and locked again the next time the unit is in home position. In the case of a power failure, both directions are locked.
alternatively
□ Aggregate type 1.2
The rigid crossbars are made of stainless steel. The tripod is electrically controlled in both directions. Through a release impulse for the entry or exit direction, the selected rotation direction is released. The rotary motion is initiated manually. In the case of a power failure, both directions are locked.
alternatively
□ Aggregate type 2
The rigid crossbars are made of stainless steel. The tripod barrier is equipped with a servo-positioning drive (low energy drive with energy content
Since the drive and the locking devices are mechanically separated, low energy drives can be used to provide personal protection. On the other hand, high locking forces can be used to prevent unauthorised passage through the unit. Parameters can be set for unit behaviour and each specific customer (e.g. starting behaviour and passage speed).
MCBF (mean cycles between failure) is 5 million.
Electrical system:
Control units and power supply unit integrated into the unit.
Power supply 100–240 V 50/60 Hz
The units with aggregate type 2 can be networked to one another.
The mechanical version (type 0) does not have a control unit or a power supply unit.
Installation:
The tripod barrier is dowelled at finished floor level FFL and is suitable for outdoor installation.
Protection class: Housing IP 33, components conducting supply voltage: IP 43
Options:
Function
Variants
Passage side inwards right / Passage side inwards left
Counter for one direction
Counter installed inside.
Permanent release in exit direction / Permanent release in entry direction
Fold down bars
The upper bar folds down when a button is pressed (on-site signal) or in the event of a power failure. The reset is initiated manually. The reset is initiated automatically for type 2 units (patented process).
Apparent installation of card reader on beveled portions of the casing,
which may be stainless steel or plastic
Concealed mounting of card readers under plastic flat panels marked with “card”Additional features
Push button on flat surface
For manual single release (installed pointing inwards).
Operating panel OPL05
For installation in flush-mounted socket with grey single installation frame. Outer dimensions: 80 mm x 80 mm. Film keypad with six push buttons and six green LEDs.
Parameters can be set for the functions depending on the unit (details can be found in document 30078).
LED arrow-cross signal device
Red/green pictogram (Ø 90 mm) installed on both sides in the housing (flat surface), intensive luminosity.
Installation of flush-mounted socket in the housing
To install components provided by the customer.
Delivery Time (standard): 15 working days
Delivery Time (with options): 25 working days