1020, 1220 mm
550, 680 mm
Upper part of the body:
The interlock has a steel structure with metal cladding.
The control unit and drive are integrated into the upper part of the body. The upper dustproof cover is made from raw aluminium plating. There is a maintenance opening in the lower ceiling plate. Two closable maintenance openings are integrated into the covers above the door leaves. The sliding wings are made of aluminium profiles with LSG 10 mm glazing flush-sealed to the outside. Moving safety strips for personal security are installed in the door leaves. There is a light scanner and a contact mat in the interlock with a zone for presence detection. Inner sidewalls limit the interlock space to the passage width of the interlock. A safety strip on the inner side wall protects fingers from getting stuck in the door leaf. Two LED lights, approx. 30,000 h service life, are integrated into the ceiling plate. Including floor element with guidance system and mounting of the security contact mat with black rubber nub covering.
Powder-coated in an RAL colour or anodised natural tone C0
(not for BR 2-S bullet-resistant glazing).
The first sliding door is opened by a motor-driven system in the direction of entry or exit by a floating release signal by the customer. The door closes and locks automatically after the inner area of the interlock has been entered. Then the second sliding door opens. After the person leaves the personal interlock, it closes and locks. If no one enters the interlock within an adjustable time period after release, the release is cancelled. There is an emergency release switch in the interlock that opens the outer door when pressed. The interlock control unit prevents both sliding doors from opening at the same time. The behaviour of the sliding doors in the event of a power failure can be freely selected. Standard adjustment is inside closed and locked, outside open.
The network-compatible CAN bus control unit is integrated into the unit. Power supply 230V AC 50/60 Hz.
Four floating inputs for on-site control and five floating outputs for further on-site processing by the customer are available.
– Passage through interlock without intermediate stop
– Passage through interlock with intermediate stop for second identification
– Passage through interlock with comfort function without intermediate stop
(deactivation of individual access control)
– Passage through interlock with with comfort function with intermediate stop for second identification (deactivation of individual access control)
– Material interlock
All processes in entry and exit direction are possible independently of one another.
(The interlock processes and time parameters usually require technical consultation. An overview of the most commonly used functions can be found in the operating instructions of the interlock).
The personal interlock is mounted on a floor element with 70 mm installation depth on the sub floor level.
Other security categories on request.
Break-in or firearm protection only on attack side (outside).
Increase upper part of body (different sizes)
Fire closure, 2-leaf
T30 by means of additional special sliding doors and respective body design for connecting to on-site fire alarm system (smoke detector and control unit provided by the customer). Installation in structural divider provided by the customer. The body on the fire protection side is made of steel, powder-coated finish in an RAL colour.
Sliding door monitoring closed
For night-time closure or fire closure. Status message closed, for on-site processing.
Manual unlocking (different solutions)
Different structures /including sensors for people crossing signaling
Contact mat two zones
Consisting of an inner “authorised” (round) and an outer “unauthorised” zone instead of single zone contact mat. The authorised zone is marked by a green rubber nub covering.
In stainless steel semi-gloss.
Powder-coated in RAL
Silver anodized C0 instead of powder-coated according to RAL colours
Different types of console for contactless readers.
Push button in stainless steel console
For manual single release, attached to the inner corner post or round body.
Push button on flat surface
For manual single release, attached to the inner corner post or round body. Integrated in flat surface and thus protected against vandalism.
Signal device in stainless steel console
Consists of 2 lights each red/green, with alternating function, attached to round body or corner post outside and inside.
Operating panel OPL 05
For installation in flush-mounted socket with single grey installation frame. Outer dimensions: 80 mm x 80 mm. Film keypad with six push buttons and six green LEDs.
Light curtain sliding door AP
Light curtain for contactless protection. Surface mounted on each unit side. Required for personal security (depending on the project risk assessment).
Scales for actual weight
Installation of a personal scale with serial transmission of the exact actual weight to the access control system. If the actual weight exceeds or falls below the permissible tolerance, the access control system is alerted. The interlock passage is terminated as “unauthorised” and the person is sent back.
Scales with one weight limit
When the set maximum weight limit is exceeded, the interlock passage is terminated as “unauthorised” and the person is sent back.
Scales with two weight limits
The reader system provided by the customer transfers the respective weight limit of the people passing through the unit. If the respective weight limit is exceeded, the interlock passage is terminated as “unauthorised” and the person is sent back.
Delivery Time (standard): 35 working days
Delivery Time (with options): 45 working days